Tym - Fender eliminators are not necessarily illegal, just that most after market ones are. Why would they could they? I guess you have to make a rule so that you can enforce it. Doesn't mean it makes sense,
Legal to drill hole in plate?
-
Naked Twin
- KSRC Regular

- Posts: 815
- Joined: Sat Jan 05, 2008 10:56 am
- Bike: Suzuki
- State: New South Wales
- Location: Sydney
Re: Legal to drill hole in plate?
Gos how many times have you been a resident of the government?
Tym - Fender eliminators are not necessarily illegal, just that most after market ones are. Why would they could they? I guess you have to make a rule so that you can enforce it. Doesn't mean it makes sense,
Tym - Fender eliminators are not necessarily illegal, just that most after market ones are. Why would they could they? I guess you have to make a rule so that you can enforce it. Doesn't mean it makes sense,
- TyM2Go
- KSRC Regular

- Posts: 594
- Joined: Wed Jan 04, 2012 2:57 pm
- Bike: Ninja 250
- State: New South Wales
- Location: Carlingford
Re: Legal to drill hole in plate?
I see, another revenue raising bullshit rule then. Ah well sort of ticked the major boxes incase a cop does pull me over. Only thing ill be fucked for is probably the mud guard as i do see a tiny bit of the "safety issue"
Was recently pulled over by the riot squad for speeding. According to them, all they heard was my exhaust taking of, but did not see me as they were behind some car's. Since i was ahead of all the cager's at the light's must mean i was speeding
Anyway's he didn't question me about my pipe being loud or anything such as that. I was doing about 60-62. Claimed it would be a loss of license if the HWP caught me. I didn't want to argue with it, as doing so would probably get my liscense suspended (not sure if riot squad has the right to issue a ticket like that) & probably booked with a defect for the pipe. He let me of with a warning and a story of 2 incident's that he witnessed.
I might add he came of at me in an aggressive manner, until i took off the helmet in a polite manner. Guess being polite & dark brown helps you out in this case
Shouldn't i be safe as there's a 3km buffer to the speedlimit? or this is invalid for P plater's
Was recently pulled over by the riot squad for speeding. According to them, all they heard was my exhaust taking of, but did not see me as they were behind some car's. Since i was ahead of all the cager's at the light's must mean i was speeding
Anyway's he didn't question me about my pipe being loud or anything such as that. I was doing about 60-62. Claimed it would be a loss of license if the HWP caught me. I didn't want to argue with it, as doing so would probably get my liscense suspended (not sure if riot squad has the right to issue a ticket like that) & probably booked with a defect for the pipe. He let me of with a warning and a story of 2 incident's that he witnessed.
I might add he came of at me in an aggressive manner, until i took off the helmet in a polite manner. Guess being polite & dark brown helps you out in this case
Shouldn't i be safe as there's a 3km buffer to the speedlimit? or this is invalid for P plater's
To be old and wise,first you need to be young and stupid
2011 Ninja 250r SE - Poison Ivy
╭∩╮(︶︿︶)╭∩╮the police.
2011 Ninja 250r SE - Poison Ivy
╭∩╮(︶︿︶)╭∩╮the police.
- Chitchats
- KSRC Regular

- Posts: 506
- Joined: Sun Apr 18, 2010 7:17 pm
- Bike: Z1000
- State: New South Wales
- Location: Parkes
Re: Legal to drill hole in plate?
I am now convinced that you are part of a benevolent scheme with this forum,
God bless us all for helping.

God bless us all for helping.
- yzr750
- KSRC Member

- Posts: 106
- Joined: Mon Jun 13, 2011 4:31 pm
- Bike: It's not worth Mentioning
- State: Queensland
Re: Legal to drill hole in plate?
Try this one, page 8.laidback wrote:Now I'm confused...I always thought the 45 deg rule applied but VSI 28 shows different...TyM2Go wrote:....Stupid question here but why are fender eliminator's illegal,
mudflaps? safety of little pebbles/ water tails?- if so car's that are in front of me in the wet and their water tail is shocking as i can't see shit unless i change lanes or slow down.
45 deg angle?- covered that
illuminated number plate - covered that
reflector- covered that
http://www.rta.nsw.gov.au/registration/ ... /vsi28.pdf
http://www.infrastructure.gov.au/roads/ ... 011_v2.pdf
- Strika
- VIP MEMBER

- Posts: 8373
- Joined: Tue Feb 01, 2005 8:02 am
- Bike: Yamaha
- State: Victoria
- Location: Melbourne
Re: Legal to drill hole in plate?
Not sure where you learnt your geometry at school, but when i learnt it, that pic of the rear guard looks to be approximately at a 45 degree angle???laidback wrote:Now I'm confused...I always thought the 45 deg rule applied but VSI 28 shows different...TyM2Go wrote:....Stupid question here but why are fender eliminator's illegal,
mudflaps? safety of little pebbles/ water tails?- if so car's that are in front of me in the wet and their water tail is shocking as i can't see shit unless i change lanes or slow down.
45 deg angle?- covered that
illuminated number plate - covered that
reflector- covered that
http://www.rta.nsw.gov.au/registration/ ... /vsi28.pdf
"I hate to advocate drugs, alcohol, violence or insanity to anyone, but they've always worked for me" Hunter S. Thompson.
There are really only two questions in life. 1.Which way do i go? 2.What is the lap record?
There are really only two questions in life. 1.Which way do i go? 2.What is the lap record?
- pittster
- KSRC Member

- Posts: 254
- Joined: Wed Mar 02, 2011 12:35 pm
- Bike: ZX10R
- State: New South Wales
- Location: Newcastle
Re: Legal to drill hole in plate?
This how you get around the fender eliminator issue. I doubt a cop would not defect you still.
BMW R1200GS Rear mudflap

BMW R1200GS Rear mudflap

Kawasaki ZX-10R 2008 - R77 Yoshi full system, PC3 Custom Mapped, Benneli bar end mirrors, Puig Double Bubble, Radiator protector, CircuitOne Mirror blanks, Pazzo levers, Shift-I, etc
Re: Legal to drill hole in plate?
That looks like an incontinence nappy for a motorcycle.I'd rather get booked
- pittster
- KSRC Member

- Posts: 254
- Joined: Wed Mar 02, 2011 12:35 pm
- Bike: ZX10R
- State: New South Wales
- Location: Newcastle
Re: Legal to drill hole in plate?
Hey I didn't say it would look good just that it bends the law a little
Kawasaki ZX-10R 2008 - R77 Yoshi full system, PC3 Custom Mapped, Benneli bar end mirrors, Puig Double Bubble, Radiator protector, CircuitOne Mirror blanks, Pazzo levers, Shift-I, etc
- laidback
- VIP MEMBER

- Posts: 3307
- Joined: Mon Mar 02, 2009 4:55 pm
- Bike: ZRX
- State: New South Wales
- Location: Wagga Wagga, NSW
Re: Legal to drill hole in plate?
Well I actually did advanced maths at school and spent 10 years as a surveyor, before the computer age where you had to know what you were doing and all calculations were manual, so I think my geometry is pretty good...Strika wrote:Not sure where you learnt your geometry at school, but when i learnt it, that pic of the rear guard looks to be approximately at a 45 degree angle???laidback wrote:Now I'm confused...I always thought the 45 deg rule applied but VSI 28 shows different...TyM2Go wrote:....Stupid question here but why are fender eliminator's illegal,
mudflaps? safety of little pebbles/ water tails?- if so car's that are in front of me in the wet and their water tail is shocking as i can't see shit unless i change lanes or slow down.
45 deg angle?- covered that
illuminated number plate - covered that
reflector- covered that
http://www.rta.nsw.gov.au/registration/ ... /vsi28.pdf
My point is...
The regulation reads "A rear wheel or sidecar wheel mudguard must extend at least from a point vertically above the
front of the tyre to a point vertically above the rear of the tyre." The diagram in yzr750's link actually shows 45 deg but this is not repeated in the text.
There is a radius (from the axle) where the 45 deg will cover from front of tyre to rear of tyre.
To demonstrate the point take the 45deg line out to double the radius of the tyre and it results in the guard having to extend well beyond the vertical line from the rear of the tyre.
If the rule is as the text shows then drop a plumb-bob from the rear of the FE and if this is rear of the tyre then it should comply (IMHO).
Roady - ZRX1200R
Tracky - ZX9R F1 Team Jerry Atric
I've reached the age where 'happy hour' is a nap.
Tracky - ZX9R F1 Team Jerry Atric
I've reached the age where 'happy hour' is a nap.
-
Stuzrx
- KSRC Member

- Posts: 301
- Joined: Thu Dec 16, 2010 6:37 am
- Bike: Z750
- State: New South Wales
- Location: Casino.
Re: Legal to drill hole in plate?
That BMW thingy is pushing the limit of the Reg I reckon.
The only thing I don't understand ,is why the mudguard ADR is so hard,apparently, for some
to understand.
The only thing I don't understand ,is why the mudguard ADR is so hard,apparently, for some
to understand.
I luurrve the smell of 2stroke in the mornin'.
'09 Z750 - '77 RD400 - '72 S1 250 Triple - '04 SV650.
'09 Z750 - '77 RD400 - '72 S1 250 Triple - '04 SV650.
- laidback
- VIP MEMBER

- Posts: 3307
- Joined: Mon Mar 02, 2009 4:55 pm
- Bike: ZRX
- State: New South Wales
- Location: Wagga Wagga, NSW
Re: Legal to drill hole in plate?
Well maybe it's my feeble old brain or the meds or both...Stuzrx wrote:That BMW thingy is pushing the limit of the Reg I reckon.
The only thing I don't understand ,is why the mudguard ADR is so hard,apparently, for some
to understand.
So what is the ADR requirement?
Roady - ZRX1200R
Tracky - ZX9R F1 Team Jerry Atric
I've reached the age where 'happy hour' is a nap.
Tracky - ZX9R F1 Team Jerry Atric
I've reached the age where 'happy hour' is a nap.
- Wattie
- VIP MEMBER

- Posts: 10041
- Joined: Mon Oct 31, 2005 12:23 pm
- Bike: ZX10R
- State: New South Wales
- Location: Bligh Park
Re: Legal to drill hole in plate?
The link YZR750 put up I'd a lot more current.laidback wrote:Well maybe it's my feeble old brain or the meds or both...Stuzrx wrote:That BMW thingy is pushing the limit of the Reg I reckon.
The only thing I don't understand ,is why the mudguard ADR is so hard,apparently, for some
to understand.![]()
So what is the ADR requirement?
So I'd guess it has been updated.
Wattie #55
ZX10R "The Crim"
ZX10R "Gumby"
Proudly Supported by Allfixed Automotive 9634 1455
sam & srt, survived
RGM, left a message
ZX10R "The Crim"
ZX10R "Gumby"
Proudly Supported by Allfixed Automotive 9634 1455
sam & srt, survived
RGM, left a message
- laidback
- VIP MEMBER

- Posts: 3307
- Joined: Mon Mar 02, 2009 4:55 pm
- Bike: ZRX
- State: New South Wales
- Location: Wagga Wagga, NSW
Re: Legal to drill hole in plate?
Yeah I can see that but everyone seems to say the rule is 45 deg.
BUT the written rule doesn't even mention 45 deg, just that it has to cover the tyre from front to back...
If you FE complied with that I reckon a good lawyer would get you off.
BUT the written rule doesn't even mention 45 deg, just that it has to cover the tyre from front to back...
If you FE complied with that I reckon a good lawyer would get you off.
Roady - ZRX1200R
Tracky - ZX9R F1 Team Jerry Atric
I've reached the age where 'happy hour' is a nap.
Tracky - ZX9R F1 Team Jerry Atric
I've reached the age where 'happy hour' is a nap.
- Wattie
- VIP MEMBER

- Posts: 10041
- Joined: Mon Oct 31, 2005 12:23 pm
- Bike: ZX10R
- State: New South Wales
- Location: Bligh Park
Re: Legal to drill hole in plate?
Yeah, but the diagram is pretty bloody clear!laidback wrote:Yeah I can see that but everyone seems to say the rule is 45 deg.
BUT the written rule doesn't even mention 45 deg, just that it has to cover the tyre from front to back...![]()
If you FE complied with that I reckon a good lawyer would get you off.
Wattie #55
ZX10R "The Crim"
ZX10R "Gumby"
Proudly Supported by Allfixed Automotive 9634 1455
sam & srt, survived
RGM, left a message
ZX10R "The Crim"
ZX10R "Gumby"
Proudly Supported by Allfixed Automotive 9634 1455
sam & srt, survived
RGM, left a message
- laidback
- VIP MEMBER

- Posts: 3307
- Joined: Mon Mar 02, 2009 4:55 pm
- Bike: ZRX
- State: New South Wales
- Location: Wagga Wagga, NSW
Re: Legal to drill hole in plate?
Still reckon it's a grey area and as this is a law then it should be clear...the diagram and the written rule should be the same.
Argumentative old fart aren't I...
When I was working as an auditor I was known as the pedantic little shit...
Argumentative old fart aren't I...
When I was working as an auditor I was known as the pedantic little shit...
Roady - ZRX1200R
Tracky - ZX9R F1 Team Jerry Atric
I've reached the age where 'happy hour' is a nap.
Tracky - ZX9R F1 Team Jerry Atric
I've reached the age where 'happy hour' is a nap.