Is it important?
It attaches to some sort of blade across the front of the motor
What is this? Off a ZZR 1200 (06)
-
RustyAs
- KSRC Member
- Posts: 353
- Joined: Sun Apr 26, 2009 8:09 pm
- Bike: ZZR1200
- State: New South Wales
- Location: Hunter Valley
What is this? Off a ZZR 1200 (06)
What is it supposed to do?
Is it important?
Im assuming the good people at Kawasaki knew what they were doing.
It attaches to some sort of blade across the front of the motor The long piece dropped down onto the hot header pipes and started to melt. frightened shit out of me. Smoke was coming out just as pulled in the driveway at home. Help
Is it important?
Im assuming the good people at Kawasaki knew what they were doing.
It attaches to some sort of blade across the front of the motor The long piece dropped down onto the hot header pipes and started to melt. frightened shit out of me. Smoke was coming out just as pulled in the driveway at home. Help
- Attachments
-
If everything is under control.......your going to slow
2012 Husaberg FE570 Dirty
2002 ZZR 1200 Roady
Bandit 1200 (Written off. My fault )
FJ 1100 ( Written off. Not my fault)
2000 ZZR 1100 (Sold)
XR 600 (630 Ballard Kit)
2012 Husaberg FE570 Dirty
2002 ZZR 1200 Roady
Bandit 1200 (Written off. My fault )
FJ 1100 ( Written off. Not my fault)
2000 ZZR 1100 (Sold)
XR 600 (630 Ballard Kit)
-
Gosling1
- Team Donut
- Posts: 13823
- Joined: Mon Jun 20, 2005 9:30 pm
- Bike: Z900
- State: ACT
- Location: Anarchy Road
Re: What is this? Off a ZZR 1200 (06)
looks like its just a bit of the cosmetic sealing stuff used over the top of the motor ? They put a lot of extraneous bullshit up there, plastic covers for the wiring loom also often have these rubber sealing doo-dads attached to them....
short answer is - the bike will run just fine without this bit of rubbery. My best guess is that it is just a bit of rubber trim that may have been attached to the lower edge of a fairing inner or something like that ?
short answer is - the bike will run just fine without this bit of rubbery. My best guess is that it is just a bit of rubber trim that may have been attached to the lower edge of a fairing inner or something like that ?
".....shut the gate on this one Maxie......it's the ducks guts !!............."
-
RustyAs
- KSRC Member
- Posts: 353
- Joined: Sun Apr 26, 2009 8:09 pm
- Bike: ZZR1200
- State: New South Wales
- Location: Hunter Valley
Re: What is this? Off a ZZR 1200 (06)
Cheers
thanks Gos. Ive been stuffing around with them for ages.
Ill just bin them now.
Cheers
Rusty
thanks Gos. Ive been stuffing around with them for ages.
Ill just bin them now.
Cheers
Rusty
If everything is under control.......your going to slow
2012 Husaberg FE570 Dirty
2002 ZZR 1200 Roady
Bandit 1200 (Written off. My fault )
FJ 1100 ( Written off. Not my fault)
2000 ZZR 1100 (Sold)
XR 600 (630 Ballard Kit)
2012 Husaberg FE570 Dirty
2002 ZZR 1200 Roady
Bandit 1200 (Written off. My fault )
FJ 1100 ( Written off. Not my fault)
2000 ZZR 1100 (Sold)
XR 600 (630 Ballard Kit)
-
bonester
- KSRC Contributor
- Posts: 2075
- Joined: Sun Apr 17, 2005 1:00 pm
- Location: Toowoomba/Ipswich Queensland
Re: What is this? Off a ZZR 1200 (06)
It's off the piece of plastic from between valve cover and radiator. Keeps hot air from carby area/ top of valve cover. Always a bitch to fit. My ZRXes have them too. Lotsa people have had them fall down onto headers. Incorrect installation I would guess. I'd rectify it. Have a look at millwaysparesonline.com.au/ for view of parts.
2 X ZRX1200R 4 X ER6N, GT550, 1988 ZX-10, 4 X GPZ250R, 4 X GPZ900R and GPZ750R 
Yeah I like Kawasakis.
Yeah I like Kawasakis.-
BrettZZR
- VIP MEMBER
- Posts: 619
- Joined: Fri Apr 13, 2012 4:44 pm
- Bike: ZZR1100
- State: Western Australia
- Location: Perth
Re: What is this? Off a ZZR 1200 (06)
Looks like yours was touching a header at some stage...
(-8
(-8