new chain

For general Technical and Performance Discussions
Post Reply
User avatar
Adel
KSRC Regular
KSRC Regular
Posts: 685
Joined: Tue Oct 10, 2006 8:36 pm
Bike: Yamaha
State: New South Wales
Location: croydon, sydney

new chain

Post by Adel »

can some help me please? I went to a bike shop today and got a new

chain put on my zxr 750 and when I took the bike for a run It starts to

get really noisey when I reach 60 k, and seems like something is holding

it from opening up slity is that normal for a new chain to do that, I did

notice the machanic put some of that white grease they put on chains,

could it be he might' ve tensioned the chain to much ? I wouldn't know guys what should the tension be

cheers fellas
ZXR 750 j 91
User avatar
MadKaw
Administrator
Administrator
Posts: 9671
Joined: Tue Apr 20, 2004 4:33 pm
Bike: ZX10R
State: New South Wales
Location: Windsor or the Creek..
Contact:

Post by MadKaw »

The chain should move up and down about 25 to 30mm on the lower side of the chain.
Also check the rear wheel alignment via the lines on the rear axle washer...
Dave
2010 Z1000
ex bikes
05 ZX-10R Race Bike - No.77
95 ZXR750R M Race Bike - No. 75
98 ZX9R Race Bike - No. 000
zx6r, zx7r, GPX750, GPX500, lots of KX's.
Image
I ride way too fast to worry about cholesterol
BladeBoy
KSRC Regular
KSRC Regular
Posts: 973
Joined: Sun Apr 10, 2005 10:18 pm
Location: Central Coast, NSW

Post by BladeBoy »

Did the mechanic replace the sprockets as well?, the chain should have about an inch movement up and down at the centre of the chain with the bike on the side stand, good luck..
Image
User avatar
Adel
KSRC Regular
KSRC Regular
Posts: 685
Joined: Tue Oct 10, 2006 8:36 pm
Bike: Yamaha
State: New South Wales
Location: croydon, sydney

Post by Adel »

I gather from your reply the noise isnt normal, well the machanic said the

sprokets look ok don't need chainging and you guys are spot on, the

chain is about an inch u n d movement, alignment also looks ok, could it be

that not enough lube on the chain?

cheers for the reply
ZXR 750 j 91
hoffy
Team Barge
Team Barge
Posts: 8744
Joined: Sun Oct 30, 2005 10:59 am
Bike: Z1000
State: New South Wales

Post by hoffy »

its hard to say, but it may just need a little wearing in ?
User avatar
javaman
VIP MEMBER
VIP MEMBER
Posts: 2473
Joined: Sun Nov 21, 2004 8:39 pm
Bike: GPz900
State: Victoria
Location: Bonbeach, VIC

Post by javaman »

I would suspect the grooves of the sprockets does not match the chain due to wear ? Try loosen up the tension to see if it gets better.

It is generally a good idea to change sprockets and chain at the same time.
alien.gif andi - Red GPZ900R, GPZ750R1, KLR650 Tengai, KLR250
"my dad's motorbike is cool it is all ways clean.oheter pepole' s motorbikes
are't like my dad's one it's because their is one not always clean."
-ariel circa 2007
http://GPZninja.blogspot.com/
User avatar
BikerBoy
KSRC Member
KSRC Member
Posts: 275
Joined: Fri Oct 06, 2006 2:14 pm
Bike: Z1000
State: New South Wales
Location: Australia

Post by BikerBoy »

I'd definitely recomment changing your sprockets when you change your chain.

The chain is much more expensive than the sprockets, so its not that expensive to do both at the same time.

I'd say thats where you problems are arising, running a new chain with semi-worn out teeth on your sprockets.

I'd try ensuring the tension is right like the guys above suggested and take it for a couple of long rides. This may help by wearing in your chain. If the problem doesn't go away, take it back and replace your sprockets too.
User avatar
MickLC
Team Crim
Posts: 5429
Joined: Wed Apr 21, 2004 1:04 pm
Bike: Z1000
State: ACT

Post by MickLC »

I agree...not changing your sprockets when doing a chain is false economy
'13 Z1000, '76 Z650+,'91 KLR250, '95 ZX6R Racebike
BladeBoy
KSRC Regular
KSRC Regular
Posts: 973
Joined: Sun Apr 10, 2005 10:18 pm
Location: Central Coast, NSW

Post by BladeBoy »

BikerBoy wrote:I'd definitely recomment changing your sprockets when you change your chain.

The chain is much more expensive than the sprockets, so its not that expensive to do both at the same time.

I'd say thats where you problems are arising, running a new chain with semi-worn out teeth on your sprockets.

I'd try ensuring the tension is right like the guys above suggested and take it for a couple of long rides. This may help by wearing in your chain. If the problem doesn't go away, take it back and replace your sprockets too.
That is if the old sprockets have not already damaged the new chain
Image
User avatar
Adel
KSRC Regular
KSRC Regular
Posts: 685
Joined: Tue Oct 10, 2006 8:36 pm
Bike: Yamaha
State: New South Wales
Location: croydon, sydney

Post by Adel »

thanks for replies I don't know much about machanicals on bikes so when machanic said you don't need to change sprokets I said you know best paid and left, if prob continues I def change the sprokets
thanks again
ZXR 750 j 91
thatp1g
Newbie
Posts: 23
Joined: Tue Sep 19, 2006 7:25 pm
Location: Sunshine Coast
Contact:

Post by thatp1g »

not 100 % happy, take it back to the shop.

You might feel a bit silly if it is nothing to worry about.

You might save yourself a bunch of money and some skin if it is something serious that they have fucked up.

Either way, up to you. But I would have it back to the shop.

If your sprockets are worn enough to make a bunch of noise then they are gonna kill your new chain in no time.
Image
User avatar
Adel
KSRC Regular
KSRC Regular
Posts: 685
Joined: Tue Oct 10, 2006 8:36 pm
Bike: Yamaha
State: New South Wales
Location: croydon, sydney

Post by Adel »

You talkd me into it, I made an appointment for bike on monday,changin the sprokets
ZXR 750 j 91
User avatar
Adel
KSRC Regular
KSRC Regular
Posts: 685
Joined: Tue Oct 10, 2006 8:36 pm
Bike: Yamaha
State: New South Wales
Location: croydon, sydney

Post by Adel »

well I got sprokets replaced, and thanks to you fellas most of the noise is gone, its much better now

cheers
adel
ZXR 750 j 91
Post Reply