We Breed "Em Tough......down at Anarchy Road ! - Video added

[Gosling1]

......Anything or anybody gos is involved with, dismantle and reassemble, look at his own dirt bike .......

Well I am glad you asked !! Here it is, for those who may not be familiar with.....the z750MX

First incarnation - small tank fitted.




Current set-up - big 19l tank, for those long mountain runs




On the summit of Mt Coree - highest mountain peak in the local ranges. Up there with my mate on his R80 G/S




On the gas in the bush. With stock road gearing, the 7fiddy chookchaser is good for >160kmh on the dirt.... but it rarely sees >140.....




There are plenty of other nutcases out there doing this shit. Here is old mate from Perth, on his Z1R....



and gettin' it sideways.....





and this is something that a good 'ole boy in the US knocked up for some hill-climb action. Thats a Z1000 motor installed into a KX500 frame ....





The old 750 has a couple of years under its belt now, and is reasonably well-sorted for the bush. It still needs the top-mounts for the rear shocks moved forward and down a bit, to gain some extra travel in the rear end. Laurie Smith, the guy doing the build on the ZX10R, was the bloke who helped me out with spring rates and shock lengths etc, when the z750 was being built. His advice was spot-on.

Apart from the suspenion mods still needed, the seat really needs a better mounting arrangement, and the starter clutch - doesn't.

But as Mick C has pointed out - the bike is really good in the dirt drags ( level-pegged Charlies KTM 590 the other weekend) , and you can basically point it anywhere that a *normal* dirt bike would go. Even steep hills and drop-off don't faze it at all. Its a great bike, and sounds shit-hot out in the boonies, with that 4-1 howl .....

I will keep this thread updated with progress on the ZX10R chookie as it develops. My input to this rig is limited...............and Jonno - I promise to get some video of the bike in action mate Should be able to jag a test-fang on it as well......

[the kid]

Love it

[Gosling1]

Here are some updated pics of this build. Laurie (owner) has been busy making a clay mold for the combined seat/tank unit. He is hoping for a capacity of about 12 litres, with a tank that also does duty as the seat base.

Here is Laurie's description of the tank/seat build.......


Notice in the pics the aluminium tray i have layed in the rear subframe,that tray will form the bottom of the fuel tank.
Upon which i will build up a mass of modeling clay and so form the shape that i desire.






The modelling clay and rods used to build the clay mold...




First i will make a spiked wooden club,lets call it the battle club.Handle and dowel shown in photo.



This battle club will be layed onto the tray first and i will buildup the clay around it.When the form is done,the battle club will allow me to lift the clay model up and suspend it. - Rough clay build-up of basic shape.



Clay has been smoothed into better shape....




Side views of clay tank/seat mold





Next is to cut some corregations into the top so as to increase the stiffness of the top of the tank,where i will sit on it.
Then start sorting out the location of the fuel filler.



Its out successfully,was heavy but manageable.Got it in my suspension vice ready to go.Will do the layup tomorrow lunchtime.






Top view of completed seat/tank mold



Bottom view of mold




First layer done.As we are all aware it was a cold night last night which was good for me.i used a fast cure hardener,but the cold slows the reaction,so when finnished i warm the part and speed up the cure.
Next is to sand and prep the part for the final layer.




And the build continues........the seat/tank unit will probably be finished during this week, as Laurie is working pretty hard on this project. I will need to be spending a few hours in his workshop one night sorting out all the electricals for the ECU etc......once thats completed, this bike will be getting pretty close.........next big job will be setting up the rear suspension with a longer shock and different linkages to obtain suspension travel that is a bit closer to a MX bike than a GP bike !!!

Stay tuned.........and I promise to get some video footage of this rig in action when Barry kicks it in the guts !!!!

[Nelso]

I love this sort of shit. The workmanship in this thing is unreal. Thanks Gos for putting it up and for the detail of the posts. I look forward to the updates.

[Damon Z1000]

Mate, love his work, mucho respect to him.
Creating from nothing gives a great sense of achievment.

10 outa 10

[funky]

Man, i wish i had half of this blokes skills, cant wait ot see the finished product

[MickLC]

and I promise to get some video footage of this rig in action when Barry kicks it in the guts !!!!

So easy?

[aardvark]

Damn.. I'm just dreaming about what this guy could do for the RD!!

[seiko1]

Holy shit, you guy's don't mess around do you!

[dutchy]

Bring it on! can't wait to see the next installment! Love ya work

[Wattie]

be worth extending the swingarm?? bit more controlable on the dirt..

[Gosling1]

and I promise to get some video footage of this rig in action when Barry kicks it in the guts !!!!

So easy?

You know how it is Mick !! a p-p-piece from here....and a p-p-piece from there !!

I will keep the updates coming on this build, Laurie also drops in here from time to time, he will be real happy with the feedback.

....be worth extending the swingarm?? bit more controlable on the dirt.. ..

Not sure if Laurie has given this any consideration at this stage....but yeh, you are spot-on - a longer swingarm could help with stability....

Once it hits the dirt for the first time.......all will be revealed ....

[the kid]

Awesome work .

[Dizzi]

This is farquing amamzing guys, hats of to you both. Like one of the others said previously the sense of achievement you guys must have to build this from scratch will be phenomanal, got me hooked on this thread now. Can't wait to see it in anction.

[smek]

Haha, wow Gos.
You certainly keep ksrc interesting!