mfzx6r wrote:aardvark wrote:Bugger. Seems I missed out by a matter of minutes. Oh well, such is life.
You should have used the nasal spray !!
Mario comes through again Jase . Grrrrrr
RGV 250...
-
the kid
- KSRC Addict
- Posts: 3948
- Joined: Thu May 12, 2005 5:10 pm
- Bike: Yamaha
- State: Victoria
- Location: Bendigo
Re: RGV 250...
Mario comes through again Jase . Grrrrrr
Ummmm let me see
-
MiG
- KSRC Member
- Posts: 356
- Joined: Tue Dec 12, 2006 9:29 pm
- Bike: It's not worth Mentioning
- State: Victoria
- Location: Bentleigh, Melbourne
Re: RGV 250...
Jesus christ! You ummed and ahhed over a complete RGV for $450?
There isn't that much that can stop it from starting. Even if the CDI is buggered, for a $130 you can get a Jaycar programmable CDI and hand controller and match the ignition curve given in the manual.
There isn't that much that can stop it from starting. Even if the CDI is buggered, for a $130 you can get a Jaycar programmable CDI and hand controller and match the ignition curve given in the manual.
KTM 640LC4 Supermoto, Booya!
-
aardvark
- Apprentice Post Whore :-)
- Posts: 5766
- Joined: Wed Apr 07, 2004 6:45 pm
- Bike: Yamaha
- State: South Australia
- Location: Adelaide, S.A.
- Contact:
Re: RGV 250...
Yeah.... didn't really need it and not really that dissapointed that I missed out.MiG wrote:Jesus christ! You ummed and ahhed over a complete RGV for $450?
-
the kid
- KSRC Addict
- Posts: 3948
- Joined: Thu May 12, 2005 5:10 pm
- Bike: Yamaha
- State: Victoria
- Location: Bendigo
Re: RGV 250...
Well I amaardvark wrote:Yeah.... didn't really need it and not really that dissapointed that I missed out.MiG wrote:Jesus christ! You ummed and ahhed over a complete RGV for $450?
PM me next time ....... just so I can get the jump on those other Bastards You had better tke it easy on the paving Mate , you are loosing it . Will send you a jar of A747 smoke to help you snap out of it .
Ummmm let me see
-
aardvark
- Apprentice Post Whore :-)
- Posts: 5766
- Joined: Wed Apr 07, 2004 6:45 pm
- Bike: Yamaha
- State: South Australia
- Location: Adelaide, S.A.
- Contact:
Re: RGV 250...
Paving is all done mate, so no need to worry there.the kid wrote:You had better tke it easy on the paving Mate , you are loosing it . Will send you a jar of A747 smoke to help you snap out of it .
As a side note, the bottom end of the RD is coming apart tomorrow. Have decided to rebuild the bottom end that Adrian obtained for me as that's already out of the bike.
-
aardvark
- Apprentice Post Whore :-)
- Posts: 5766
- Joined: Wed Apr 07, 2004 6:45 pm
- Bike: Yamaha
- State: South Australia
- Location: Adelaide, S.A.
- Contact:
Re: RGV 250...
Well, I was thinking about taking it to Ian Williams at Ian Williams Tuning or down to the guys at Hoey's. Unless you know of someone else over this way?the kid wrote:Good idea . Have you got someone to do the job ?