ZX7R P2 Green Meanie (Repost with smaller pix)

Show us your happy snaps here
Post Reply
Norman Peters
Newbie
Posts: 4
Joined: Fri Oct 06, 2006 2:58 pm
Location: Canberra

ZX7R P2 Green Meanie (Repost with smaller pix)

Post by Norman Peters »

1997 ZX7R P2

It has braided front brake lines, revised fork valving & suspension setup for me front & rear, courtesy of "Suspension Smith" in Fyshwick, ACT. Also heated grips, ZX7-RR rear suspension unit, Yoshimura RS3 pipe and custom-made stainless interconnect, and the best bit, sheepskin covers for the seats. I have a K&N high-flow air filter to fit waiting at home, but I am delaying until after the next big service (48,000 kms) when I will get Axel's to dyno it and fit the filter then, along with a Factory Pro jet kit, to liberate another few hp.

New tyres will follow that to replace my squared-off Dunlops D208s (too many Sydney trips recently) - thinking of Michelin Pilot Road rear and Pilot Power front - any suggestions?
Attachments
bike2.jpg
bike2.jpg (340.43 KiB) Viewed 1258 times
bike1.jpg
bike1.jpg (285.55 KiB) Viewed 1257 times
hoffy
Team Barge
Team Barge
Posts: 8744
Joined: Sun Oct 30, 2005 10:59 am
Bike: Z1000
State: New South Wales

Post by hoffy »

Very clean mate, and welcome to the club.
Love the sheepskins, I gotta get me sum of those for the tourer.

There is many a current or ex 7 owner amongst us to chew the fat with.

If ya get up to Syd regulary, i'll maybe see you at the aus supers in Nov.
L3raven
KSRC Member
KSRC Member
Posts: 261
Joined: Thu Aug 04, 2005 1:31 am
Bike: ZX7R
State: Western Australia
Location: perth wa

Post by L3raven »

Nice ride bro, welcome i own a semi race L3
Pops the clutch n falls off haha!!
User avatar
Colette
Team Cougar
Posts: 3089
Joined: Thu Apr 22, 2004 10:20 am
Bike: ZX6R
State: New South Wales

Post by Colette »

Looks great :)

I've just had my forks and springs revalved and regassed at Teknik in Penrith...how are you finding your new setup?
Norman Peters
Newbie
Posts: 4
Joined: Fri Oct 06, 2006 2:58 pm
Location: Canberra

Suspension setup

Post by Norman Peters »

Hi Colete -

I have a ZX7RR rear-end, with far more adjustment than on a standard 7R, and at the front, standard springs (I am heavy so they work fine for me) and new compression and rebound valving. The forks are dropped about 6mm, plus the front/rear ride height has been set to give me pretty fast steering on the 190 section rear I use. The sag and everything else was set for me in riding gear, so its pretty well dialled infor me

Let me put it this way - I though the bike handled well before, but now its amazing. I sure can tell I need a new rear.....
User avatar
Colette
Team Cougar
Posts: 3089
Joined: Thu Apr 22, 2004 10:20 am
Bike: ZX6R
State: New South Wales

Post by Colette »

Thanks Norman, that's good to know it has worked well for you :)

Mine was lowered by 50mm and we adjusted brake and clutch cable before I left the shop. It's a brand new bike so there is much to get used to, but so far the setup feels right for me, which is the main thing :)
FrogZ
KSRC Contributor
KSRC Contributor
Posts: 2090
Joined: Tue Apr 11, 2006 12:58 pm
Location: Rockhampton CQ

Post by FrogZ »

Norm, Michies Pilots are EXCELLENT on a ZX7R
Do go for a 180 rear too, MUCH better... :wink:
Just because you CAN ride, doesn't mean you SHOULD
Post Reply