Kawasaki Sportsbike Riders Club - Australia - Online Forum

And spray putty then spot putty more primer and more spot putty then Ahhhhhhhhhhh Fuck it , its only race glass





Oh , anyone tried to knock a dit outta a tank ????

swabio-ACT wrote: Oh and I discovered I am an absolute bog numpty! How the hell do you get that shit down somewhat smooth? I envisage having the bike finished by monday afternoon...

An old trick matey...........
Apply filler slightly higher than surrounding area......sneak into the other half's domain and pinch the glad wrap outa the kitchen before the missis spots you......... apply over the filler and pull the filler into shape using the glad wrap and stick to the surrounding area to be filled. Leave for 15 to 30 mins depending on the filler your using before removing the film

Fark........You lot will soon have picked me brains clean

the kid wrote:And spray putty then spot putty more primer and more spot putty then Ahhhhhhhhhhh Fuck it , its only race glass

Oh , anyone tried to knock a dit outta a tank ????

No but I once pulled a dint out of 1

I'll talk you thru it at Halls Gap..............2nd thoughts neither of us would remember

Drain fuel........Flush with copious amounts of water to remove all traces of fuel....weld a bolt to the centre of the dint and attatch to slide hammer.......pull it out ( oooo errr missis), grind off bolt carefully fill, sand & paint to match surrounding area

IF only it was as easy as typing instructions

Onya Swabbie looks TOPS

Rossi wrote:

the kid wrote:And spray putty then spot putty more primer and more spot putty then Ahhhhhhhhhhh Fuck it , its only race glass

Oh , anyone tried to knock a dit outta a tank ????

No but I once pulled a dint out of 1

I'll talk you thru it at Halls Gap..............2nd thoughts neither of us would remember

Drain fuel........Flush with copious amounts of water to remove all traces of fuel....weld a bolt to the centre of the dint and attatch to slide hammer.......pull it out ( oooo errr missis), grind off bolt carefully fill, sand & paint to match surrounding area

IF only it was as easy as typing instructions

So what's Stace going to think of you welding his bolt to your tank at Halls Gap?

a new pic n comment... se 1st post....

Mick C wrote:

Rossi wrote:

the kid wrote:And spray putty then spot putty more primer and more spot putty then Ahhhhhhhhhhh Fuck it , its only race glass

Oh , anyone tried to knock a dit outta a tank ????

No but I once pulled a dint out of 1

I'll talk you thru it at Halls Gap..............2nd thoughts neither of us would remember

Drain fuel........Flush with copious amounts of water to remove all traces of fuel....weld a bolt to the centre of the dint and attatch to slide hammer.......pull it out ( oooo errr missis), grind off bolt carefully fill, sand & paint to match surrounding area

IF only it was as easy as typing instructions

So what's Stace going to think of you welding his bolt to your tank at Halls Gap?

OUCH . good work swabio , go to the local paint shop or hardware store & get a coupla sponge sanding blocks these will make the sanding of bog overfill much easier,still use with water but.

Leave it primered! ... our bikes will just about be matching then!
"team Green" at Wakefield can be "Team Primer (and Dave)"

or DP, you could get off your ass and paint yours

trust me, I have not spent all this time and effort to scoot around on a grey primered bike! talk about driving me nuts! hmmm no time to sand today, have to go get a needle, damn japanese encephalytis injection better not make me sick!

updated with pix, see first post again.....

Before I check the monitor what colour green is that..... is it close to kwakka green? BTW looks like a great job.... wanna do mine? wanna do Caths?

Mick C wrote:

Rossi wrote:

the kid wrote:And spray putty then spot putty more primer and more spot putty then Ahhhhhhhhhhh Fuck it , its only race glass

Oh , anyone tried to knock a dit outta a tank ????

No but I once pulled a dint out of 1

I'll talk you thru it at Halls Gap..............2nd thoughts neither of us would remember

Drain fuel........Flush with copious amounts of water to remove all traces of fuel....weld a bolt to the centre of the dint and attatch to slide hammer.......pull it out ( oooo errr missis), grind off bolt carefully fill, sand & paint to match surrounding area

IF only it was as easy as typing instructions

So what's Stace going to think of you welding his bolt to your tank at Halls Gap?

what this one

looks good so far mate .

robracer wrote:Before I check the monitor what colour green is that..... is it close to kwakka green? BTW looks like a great job.... wanna do mine? wanna do Caths?

Mate, it is a green that I got the dude to make up on the bench.... just kept saying.... more green or more mettalic..... I am happy with the colour though!

Can't wait to get the bbbiatch finished though! I almost died in my dodgy tent of death spray booth that i made up... lol, was funnier when I realised I also had a 3m x 3m green patch of driveway.........

NEW PIX>>>>> see post 3!