ZXR750 The Tale of Woe to Go

BLOOzx9 · Post by **BLOOzx9** » Thu Jan 12, 2006 12:15 pm

that'll be unreal when you finish it. make sure you re-instate the 'hoover' tubes tho! they're what made this model special!

is it worth rebuilding the old zxr engine? it would cost lots and there are other options as far as power plant goes...

theres a 98 zx9r engine on ebay at the moment... (no, its not mine) that would make more than enough power for the chassis.

i'm about to put a 98 zx9 engine into a 95 zxr streetfighter chassis, so i'll be sure to stay tuned...

Post by **MadKaw** » Thu Jan 12, 2006 12:56 pm

BLOOzx9 wrote:that'll be unreal when you finish it. make sure you re-instate the 'hoover' tubes tho! they're what made this model special!

is it worth rebuilding the old zxr engine? it would cost lots and there are other options as far as power plant goes...

theres a 98 zx9r engine on ebay at the moment... (no, its not mine) that would make more than enough power for the chassis.

i'm about to put a 98 zx9 engine into a 95 zxr streetfighter chassis, so i'll be sure to stay tuned...

I don't know for sure but I didn't think the 98 + zx9r motor fitted into the zxr 750 chassis as its too wide. I know the 95 to 97 zx9r fitted quite well..
I've seen that coversion on 91 to 2000 zx7's unfortunately for Mick I've never seen it on the 89...

Heres some info.
http://homepage.ntlworld.com/webzxr/zxr ... xr7-9.html

James · Post by **James** » Thu Jan 12, 2006 3:45 pm

Smitty wrote:
anyone else got an old ZXr750 they want to get rid of....

cheers

I have one

Tape - about the motor. The H1 motor was a retuned GPX750 motor. From what I can gather, the overseas H1's had the letters "H1" in the engine number, whereas as ours have the "FE" letters instead. The "FE" lettering in the engine number signify it as being a GPX750 block. So I guess a GPX motor may fit straight in.

I hope this helps.

diesel · Post by **diesel** » Thu Jan 12, 2006 5:02 pm

didn't read every post, but i reckon go with a 9 motor if you can.
but that may not be as fun as putting the 7fiddy back together.

gove us a shout when u need a hand. i'm nly round the corner.
well..... 8 actually

Stereo · Post by **Stereo** » Wed Jan 18, 2006 7:31 am

Is it finished yet?

Nanna10r · Post by **Nanna10r** » Wed Jan 18, 2006 9:30 am

Stereo wrote:Is it finished yet?

Pics or it didnt happen ?.
I wonder where T is going to put her new Table lamps ?.
Cheers Big Ears.

tape · Post by **tape** » Sun Jan 22, 2006 9:55 pm

Stereo wrote:Is it finished yet?

Nah Stereo, still is in same condition as the posted pics due to having a holiday.

The project starts now, so all will be annoyed with stupid questions of "how to and what if's", but I'm sure with your knoweldge of bikes you will be of major assistance as will many others.

cheers

Johnnie5 · Post by **Johnnie5** » Mon Jan 23, 2006 2:27 pm

Smitty wrote:
T wrote:
anyone else got an old ZXr750 they want to get rid of....

cheers

not getting mine

had it over 10 years , about time it went back on the road

when i pull finger out will be going back together with

810cc
muzyz head
muzzy cams
kit gearbox

anyone got a pipe kicking around ??

mike-s · Post by **mike-s** » Mon Jan 23, 2006 3:12 pm

Your right, the more i look at it, the more it *DOES* resemble a GPX750 donk

.

Does this mean i can drop a zx9 into the GPX 7fiddy chassis?

Neka79 · Post by **Neka79** » Mon Jan 23, 2006 8:55 pm

tape wrote:
Stereo wrote:Is it finished yet?
Nah Stereo, still is in same condition as the posted pics due to having a holiday.

The project starts now, so all will be annoyed with stupid questions of "how to and what if's", but I'm sure with your knoweldge of bikes you will be of major assistance as will many others.

cheers

carn tape..wots keeping ya mate??
this whole "family" thing can b a bit of a distraction me thinks...tho if u sell a couple of em u might get sum extra $$ for the new donk??

Stereo · Post by **Stereo** » Tue Jan 31, 2006 6:57 am

Is it finished now?

Duane · Post by **Duane** » Tue Jan 31, 2006 7:27 am

Pics or it didnt happen.

If it's not done yet, it must be gregs fault!

tape · Post by **tape** » Wed Feb 01, 2006 7:37 pm

Stereo wrote:Is it finished now?

Waiting for you to offer your assistance Eelko, with your greater knowledge and my money tree that we have in the back yard it'll be finished in no time...

Seriously though, bought some polishing stuff and a rotary tool today so ant spare moments will be out in the shed. Though I do need a fridge for out there if anyone has one they want rid of (working).

I need to know if anyone can suggest a motor reco place, one that know their stuff hopefully....

Also, if anyone knows what the 2 welded nut thingies are on the swingarm on left hand side, (see pic) are for please help.

cheers and if ya want to seriously help PM me ya phone numbers so I can pick ya brains....rofl

tape · Post by **tape** » Wed Feb 01, 2006 7:47 pm

James I hope ya don't miind me using ya pic, it was the best one I could find. If you have a concern let me know and I'll remove it.

Cheers

James · Post by **James** » Wed Feb 01, 2006 8:33 pm

Go right ahead mate, no worries

Can you give me some info about the rotary tool / policher you bought today? Ive been looking for something to polish my shiny bits with.

Those little thingies are for the end of the chain guard Im guessing. Like this one: