I let the smoke out.... Now what

For general Technical and Performance Discussions

I let the smoke out.... Now what

Postby timeeh » Sat May 25, 2019 1:46 pm

Hi guys, long time no post... Or read for that matter. However, I need some advice if I may. About 1mth ago, I was riding along and noticed a fair bit of smoke around, then realised it was all coming from me... Somehow the bike managed to throw the water in with the oil to not a great effect. Anyway pulled up before I believe any major damage as performance didn't drop and the engine certainly didn't sieze. So now I'm wondering what to do for here, is it salvageable? And want proceedure do you think I should take to find out the cause? The bike is a 96 zx9 with just on 30k so I don't believe it's anywhere near its EOL. Thoughts?
timeeh
Warming up
Warming up
 
Posts: 58
Joined: Wed Mar 13, 2013 10:06 am
Bike: ZX9R
State: ACT

Re: I let the smoke out.... Now what

Postby billwest » Sat May 25, 2019 4:27 pm

Where do you think the water went? In the oil? Is it milky white?

Is the crankcase breather still attached properly?
Don't ride as if you own the road.......
Ride as if you own the bike!

ZZR1200 ('02), FJR1300 ('19).
User avatar
billwest
VIP MEMBER
VIP MEMBER
 
Posts: 387
Joined: Sat Jan 28, 2006 8:49 pm
Location: Perth, WA
Bike: ZZR1200
State: Western Australia

Re: I let the smoke out.... Now what

Postby timeeh » Sat May 25, 2019 6:18 pm

Yep, water went into the crankcase, was all milky and spilling out the head gasket (producing the smoke)
timeeh
Warming up
Warming up
 
Posts: 58
Joined: Wed Mar 13, 2013 10:06 am
Bike: ZX9R
State: ACT

Re: I let the smoke out.... Now what

Postby billwest » Sun May 26, 2019 11:22 am

How is your coolant level?
Coming out of the head gasket? Isn't the head torqued down properly?
Don't ride as if you own the road.......
Ride as if you own the bike!

ZZR1200 ('02), FJR1300 ('19).
User avatar
billwest
VIP MEMBER
VIP MEMBER
 
Posts: 387
Joined: Sat Jan 28, 2006 8:49 pm
Location: Perth, WA
Bike: ZZR1200
State: Western Australia

Re: I let the smoke out.... Now what

Postby timeeh » Sun May 26, 2019 11:27 am

Coolant is now empty (at least the bottle). I've removed the water pump to see if that was siezed and water came out so still water left in the water system, and no the pumps not siezed). Could just be the head needs to the torqued down. Might check the bolts today and see if there out. Also by doing this the gasket would still need replacing would it not?
timeeh
Warming up
Warming up
 
Posts: 58
Joined: Wed Mar 13, 2013 10:06 am
Bike: ZX9R
State: ACT

Re: I let the smoke out.... Now what

Postby billwest » Sun May 26, 2019 11:42 am

"A leaking head gasket can also cause problems with your motor as coolant is drawn into the combustion chamber. ... If your head gasket is damaged enough to allow a leak, then the leaking water and pressure can erode the metal of your head and engine block at the leak point."

(from: https://gobdp.com/blog/can-drive-leaking-head-gasket/ )

How are your plugs?
Compression test?
Does it run like crap?
Don't ride as if you own the road.......
Ride as if you own the bike!

ZZR1200 ('02), FJR1300 ('19).
User avatar
billwest
VIP MEMBER
VIP MEMBER
 
Posts: 387
Joined: Sat Jan 28, 2006 8:49 pm
Location: Perth, WA
Bike: ZZR1200
State: Western Australia

Re: I let the smoke out.... Now what

Postby timeeh » Sun May 26, 2019 4:22 pm

Haven't done any of the above but it was running perfectly until it started smoking (even then it was running fine, I killed the engine as soon as I could to prevent further damage). I did recently change the water pump with one of a zx7 as the old one was leaking from the weap hole, and the one of the zx7 does not have a weep hole? But it did the job, which is why that was the first thing I checked after, but it seems fine, although I can't check the main seal in this... I'm thinking head gasket but just checking where else I should look first before pulling the head off
timeeh
Warming up
Warming up
 
Posts: 58
Joined: Wed Mar 13, 2013 10:06 am
Bike: ZX9R
State: ACT

Re: I let the smoke out.... Now what

Postby BrettZZR » Sun May 26, 2019 4:59 pm

Sounds like you need a head job more then the rest of us!

It's a bit of a snowball:
In theory you could just replace the headgasket, but really you should give a light skim on the head and barrels. That cannot be done without pulling the pistons out the barrels, and best to strip the valves out the head. So you may as well hone the bores and fit new pistons, and do a nice 5 angle valve job, and (at least) de-carbon the ports. While you are doing that you may-aswell ... Uh-oh, you just got hit by a snowball!

(-8
User avatar
BrettZZR
VIP MEMBER
VIP MEMBER
 
Posts: 604
Joined: Fri Apr 13, 2012 4:44 pm
Location: Perth
Bike: ZZR1100
State: Western Australia

Re: I let the smoke out.... Now what

Postby billwest » Sun May 26, 2019 6:40 pm

Is it smoke from oil, or just water vapour?
Don't ride as if you own the road.......
Ride as if you own the bike!

ZZR1200 ('02), FJR1300 ('19).
User avatar
billwest
VIP MEMBER
VIP MEMBER
 
Posts: 387
Joined: Sat Jan 28, 2006 8:49 pm
Location: Perth, WA
Bike: ZZR1200
State: Western Australia


Return to General Tech & Performance Talk

Who is online

Users browsing this forum: No registered users and 12 guests

cron