ZZR1200 Rear Shock

ZZR 250, 600, 1100 & 1200

ZZR1200 Rear Shock

Postby billwest » Tue Jul 17, 2018 4:37 pm

I replaced my rear shock with a somewhat newer ZZR OEM one.
Details here.

Riding and cornering is much nicer now.
I did dial it in a bit differently than the old one.
I put preload at around 4.5 (old one was 3.5), and damping adjustment at 3 (2 on the old one).
I weigh around 100kg.

So far so good.
Last edited by billwest on Wed Feb 06, 2019 12:57 pm, edited 1 time in total.
Don't ride as if you own the road.......
Ride as if you own the bike!

ZZR1200 ('02), FJR1300 ('19).
User avatar
billwest
VIP MEMBER
VIP MEMBER
 
Posts: 387
Joined: Sat Jan 28, 2006 8:49 pm
Location: Perth, WA
Bike: ZZR1200
State: Western Australia

Re: ZZR1200 Rear Shock

Postby BrettZZR » Tue Jul 17, 2018 4:55 pm

Mmmm... Is the old one rebuild-able? It is exactly the same size as the 11's all round except for the fork width of the bottom bracket being a few mm narrower on the 1200 unit.

Would you flog it for an inconceivably small amount of cash? If it's rebuild-able then it might be a good "upgrade" with the remote adjustment etc etc?

Dunno. Better bust out a few of my workshop manuals...

(-8
User avatar
BrettZZR
VIP MEMBER
VIP MEMBER
 
Posts: 604
Joined: Fri Apr 13, 2012 4:44 pm
Location: Perth
Bike: ZZR1100
State: Western Australia

Re: ZZR1200 Rear Shock

Postby billwest » Tue Jul 17, 2018 5:08 pm

I don't know about rebuildable, but have a read of this.

I emailed them, and they said they could do it for around $800.

Ikon pic:

ikon.jpg
ikon.jpg (147.34 KiB) Viewed 31123 times


I was thinking of keeping mine in case I want to do the Ikon thing. I can then send it away while still having a shock on the bike.
Don't ride as if you own the road.......
Ride as if you own the bike!

ZZR1200 ('02), FJR1300 ('19).
User avatar
billwest
VIP MEMBER
VIP MEMBER
 
Posts: 387
Joined: Sat Jan 28, 2006 8:49 pm
Location: Perth, WA
Bike: ZZR1200
State: Western Australia

Re: ZZR1200 Rear Shock

Postby BrettZZR » Tue Jul 17, 2018 11:27 pm

billwest wrote:... keeping mine in case ...

Fairy Nuff... Makes sense.

12 unit is pressurised, and the workshop manual doesn't mention rebuilding, not that that means it can't be done.

Might keep a butchers hook out for a cheapie, and have a poke and prod (sometime in the next milennium when I have some free time!)

(-8
User avatar
BrettZZR
VIP MEMBER
VIP MEMBER
 
Posts: 604
Joined: Fri Apr 13, 2012 4:44 pm
Location: Perth
Bike: ZZR1100
State: Western Australia

Re: ZZR1200 Rear Shock

Postby billwest » Mon Jul 30, 2018 11:21 am

Brett, how small an amount were you thinking?
I'm considering $50.

Bill.
Don't ride as if you own the road.......
Ride as if you own the bike!

ZZR1200 ('02), FJR1300 ('19).
User avatar
billwest
VIP MEMBER
VIP MEMBER
 
Posts: 387
Joined: Sat Jan 28, 2006 8:49 pm
Location: Perth, WA
Bike: ZZR1200
State: Western Australia

Re: ZZR1200 Rear Shock

Postby BrettZZR » Mon Jul 30, 2018 2:38 pm

Could work - I'll swing past sometime and have a look.
User avatar
BrettZZR
VIP MEMBER
VIP MEMBER
 
Posts: 604
Joined: Fri Apr 13, 2012 4:44 pm
Location: Perth
Bike: ZZR1100
State: Western Australia

Re: ZZR1200 Rear Shock

Postby billwest » Thu May 30, 2019 10:18 am

It is still here, Brett .....
Could go for $40.
Don't ride as if you own the road.......
Ride as if you own the bike!

ZZR1200 ('02), FJR1300 ('19).
User avatar
billwest
VIP MEMBER
VIP MEMBER
 
Posts: 387
Joined: Sat Jan 28, 2006 8:49 pm
Location: Perth, WA
Bike: ZZR1200
State: Western Australia

Re: ZZR1200 Rear Shock

Postby billwest » Tue Nov 17, 2020 10:39 pm

I went for the Ikon rear shock not too long ago.
I had a few fitting issues.


Fitting......

The top eye is narrower than the OEM one, so Ikon supplied a couple of spacers.
The OEM top bolt does not fit through them. It stops where the threaded bit ends. At that point the bolt has a slightly larger diameter.

I went to my local "Nuts and Bolts" shop, and they had a similar bolt (high tensile) which exactly fits the spacers.

So, that bit solved.

The OEM bolt doesn't fit the bottom fitting either. I drilled the holes out slightly.
The bottom fitting needed attention. It is narrower by a fraction, than the OEM.
The distance has to cater for a fixed width spacer
I bent the ends out slightly, and removed a very small amount of material from around and above the bolt holes. Once attached, the ends pulled together again.
It fits.

I couldn't wait any longer. I went for a ride (it's been over 3 months - shoulder surgery); shoulder actually feels pretty ok.
The new shock feels good, and seems to soak up the bumps better. I adjusted preload a couple of times, and I think I'm close to getting it right.
I initially had the adjuster at 3.5 (had that with the old shock), now back down to 2.0. Damping I have set at #2, and I may drop it down a bit.

New silencers (Black Widows) are excellent, very nice sound. I have left the dbKillers in, but I chopped off the end caps. It is just too loud with them out.
I just can't get over how good this 2002 bike still is!
PR5's all round.

IMG_5477.JPG
Don't ride as if you own the road.......
Ride as if you own the bike!

ZZR1200 ('02), FJR1300 ('19).
User avatar
billwest
VIP MEMBER
VIP MEMBER
 
Posts: 387
Joined: Sat Jan 28, 2006 8:49 pm
Location: Perth, WA
Bike: ZZR1200
State: Western Australia


Return to ZZR Discussion

Who is online

Users browsing this forum: Google [Bot] and 7 guests

cron