Have replaced ecu & wiring harness with an american setup but still no fuel pump or servo motor
any ideas to get the girl going? cheers Bwz1a
Kawasaki Sportsbike Riders Club - Australia - Online Forum
Australian Kawasaki Sportsbike Riders Discussion Forum - All Welcome, free and easy to join, just click "register" below - www.ksrc-au.com
07zx10 wiring ??
6 posts
• Page 1 of 1
07zx10 wiring ??
by bwz1a » Tue Mar 02, 2010 1:58 pm
- bwz1a
- Newbie
- Posts: 10
- Joined: Sat Aug 30, 2008 2:21 pm
- Location: Chipping Norton NSW
- Bike: Z1000
- State: New South Wales
Re: 07zx10 wiring ??
by Wattie » Tue Mar 02, 2010 3:55 pm
kill switch?
in gear?
clutch switch? sidestand switch?
in gear?
clutch switch? sidestand switch?
Wattie #55
ZX10R "The Crim"
ZX10R "Gumby"
Proudly Supported by Allfixed Automotive 9634 1455
sam & srt, survived
RGM, left a message
ZX10R "The Crim"
ZX10R "Gumby"
Proudly Supported by Allfixed Automotive 9634 1455
sam & srt, survived
RGM, left a message
-
Wattie - VIP MEMBER
- Posts: 10041
- Joined: Mon Oct 31, 2005 12:23 pm
- Location: Bligh Park
- Bike: ZX10R
- State: New South Wales
Re: 07zx10 wiring ??
by Gosling1 » Tue Mar 02, 2010 5:34 pm
Australian harness ?? (maybe the US stuff has some pollution control that we don't, the ECU is not sensing it, so no start ?)
".....shut the gate on this one Maxie......it's the ducks guts !!............."
-
Gosling1 - Team Donut
- Posts: 13823
- Joined: Mon Jun 20, 2005 9:30 pm
- Location: Anarchy Road
- Bike: Z900
- State: ACT
Re: 07zx10 wiring ??
by bwz1a » Wed Mar 03, 2010 3:57 pm
Thanks for the input ,
I found the side stand connection & bridged them out & it started
the servo mtr worked as you accellerated so i thought it was sorted!
I turned it off after running it for 5 minutes to tape up unused wires & sure enough it wont start again
HELP !
I found the side stand connection & bridged them out & it started
the servo mtr worked as you accellerated so i thought it was sorted!
I turned it off after running it for 5 minutes to tape up unused wires & sure enough it wont start again
HELP !
- bwz1a
- Newbie
- Posts: 10
- Joined: Sat Aug 30, 2008 2:21 pm
- Location: Chipping Norton NSW
- Bike: Z1000
- State: New South Wales
Re: 07zx10 wiring ??
by greenman43 » Thu Mar 04, 2010 11:59 am
Definitely nothing to do with the clutch cut-out switch that Wattie mentioned, Gary ?
BTW, are you going to be in on Saturday morning ? I can possibly get over (pretty early) and drop the wheel off.
Cheers,
Brian
BTW, are you going to be in on Saturday morning ? I can possibly get over (pretty early) and drop the wheel off.
Cheers,
Brian
07 ZX10R track 09 ZX6R road/track 93 ZXR750 race 89 GPZ900 project
Do not walk behind me, for I may not be leading
Do not walk in front of me, for I may not be following
Do not walk alongside me, for the path may be narrow
Just piss off and leave me alone
Do not walk behind me, for I may not be leading
Do not walk in front of me, for I may not be following
Do not walk alongside me, for the path may be narrow
Just piss off and leave me alone
-
greenman43 - KSRC Regular
- Posts: 675
- Joined: Fri May 06, 2005 10:01 pm
- Location: Brooklyn NSW
- Bike: ZX6R
- State: New South Wales
Re: 07zx10 wiring ??
by bwz1a » Thu Mar 04, 2010 8:41 pm
Getting hold of a workshop manual for the fault codes to sort iy !!!
Thanks Brian see you sat
cheers Gary
Thanks Brian see you sat
cheers Gary
- bwz1a
- Newbie
- Posts: 10
- Joined: Sat Aug 30, 2008 2:21 pm
- Location: Chipping Norton NSW
- Bike: Z1000
- State: New South Wales
6 posts
• Page 1 of 1
Return to ZX-R / Ninja Current Model Discussion
Who is online
Users browsing this forum: No registered users and 8 guests