Page 1 of 3
crash protectors/ frame sliders/ crash knobs etc
Posted:
Tue Jan 23, 2007 5:53 pmby Wardy
Just after some opinions on what is the best for crash protectors for a 00/01 zx9.
I had R&G racing ones on in my spill at OP on the weekend and they did the job but now their farked (rh snapped clean off, lh bent at 45 degrees and worn down). So I need replacement ones. These ones are £80.85 excl. VAT etc.
cheers
Russ
Posted:
Tue Jan 23, 2007 8:14 pmby dave#3
I've got the R&G ones, and though I haven't tested them, the fact that they bent and broke in an off is a good thing as far as I'm concerned - they're designed to give out before damaging the frame.
I think £80.85 is pretty reasonable considering the replacement cost of the fairings they saved.
Posted:
Wed Jan 24, 2007 5:28 amby Wardy
Yeah agreed, the bolts are actually designed to snap before bending the frame/engine mounts etc.
Posted:
Wed Jan 24, 2007 5:12 pmby mrmina
i got mine from NZ for $60 or something like that.
Posted:
Thu Jan 25, 2007 1:50 pmby NovaCoder
Go R&G they are the best!
My race bike is now just one big crash protector with a wheel at each end.
Posted:
Thu Jan 25, 2007 4:47 pmby mrmina
doesn't it have an engine
Posted:
Thu Jan 25, 2007 5:22 pmby balanse
I am curious too, are these things really any good.
I have thought about getting them for the ZRX on and off but can't come to a conclusion in mind about their value in a crash.
Seem to be bloody expensive for skate board wheels too.
Posted:
Thu Jan 25, 2007 6:29 pmby Strika
balanse wrote:I am curious too, are these things really any good.
I have thought about getting them for the ZRX on and off but can't come to a conclusion in mind about their value in a crash.
Seem to be bloody expensive for skate board wheels too.
Mate you could turn some up just as easy out in the shed over a couple of well rolled spliffs!!!
They are only made of hard urethane of some description. Can't be too hard! And Keables will have some bolts
Posted:
Thu Jan 25, 2007 9:08 pmby GlennB
dont get the mini crash knobs! I took the tight arse way and got a pair of them and I come off the bike a month or so ago and it snaped off and put a huge farking hole in my fairing.
R&G sounds the way to go.
Posted:
Sun Jan 28, 2007 6:27 pmby Wardy
Well bit the bullet and ordered another set of R&G ones from AMC.
Posted:
Mon Jan 29, 2007 1:30 pmby Grasshopper
i coughed up for crash's.
reckon i could have come up with something VERY similar using skateboard wheels.
Posted:
Thu Mar 15, 2007 11:52 pmby portaz
So im lookin for crash knobs for my 05 zx636... where can i pick some up r&g knobs for a decent price??
Posted:
Fri Mar 16, 2007 4:08 pmby dave#3
Get 'em direct from the manufacturer at
http://www.rg-racing.com/. It's quicker and cheaper than buying through the Australian distributor (and you're less likely to have to send them back, wait another 6 weeks for the replacements ... grrrr.....)
Posted:
Sat Mar 17, 2007 12:34 pmby Wardy
portaz wrote:So im lookin for crash knobs for my 05 zx636... where can i pick some up r&g knobs for a decent price??
My wife has an 06 636 and bought crash knobs, they had all the brackets etc and seem to be pretty good.
Posted:
Sat Mar 17, 2007 11:35 pmby portaz
russ_2000_zx9 wrote:portaz wrote:So im lookin for crash knobs for my 05 zx636... where can i pick some up r&g knobs for a decent price??
My wife has an 06 636 and bought crash knobs, they had all the brackets etc and seem to be pretty good.
yeh i was thinking crash knobs aswell... where bouts did you get them from, how for how much?