yep need an ohlins and other misc' bits

[Jonno]

They said the OEM shock on the 2011 ZX10 wouldnt cut it on the track, absolutely correct. Shocking really

Didnt realise how bad until i seen this pic of it squatting, sags were set and comp was dialled all the way and back a wisker.
Looking through the other JPM photo's in this group no other bike was displaying this.

EC T9.jpg (115.56 KiB) Viewed 2098 times

Could feel it scrape a few times, brings back memory's of the 12R's doing the same.

little scratch.jpg (148.49 KiB) Viewed 2098 times

It was being a bit wheelie happy even with TC mode on and my boots were constantly being smashed into the tarmac which effectively had me re-adjusting my line.

rearsets 2.jpg (165.5 KiB) Viewed 2098 times

Next: install plastic tube to replace master cylinder.

rearsets 6.jpg (187.21 KiB) Viewed 2098 times

I will remove the ABS fuse as the brakes were quite wooden and a little bit unpredictable in ways when that kicked in, Bendix competition pads go in for a try out.. Was told it is just the fuse, then i have heard conflicting advice so anyhoo give it a whirl and see.

Replaced that brain buzzing Akrapovic shorty with a Leo Vince link and SBK muffler thanks to Maccarocks. Deeper and a bit quieter.

rearsets 1.jpg (193.06 KiB) Viewed 2098 times

[Strika]

Jonno, don't fuck around with your Ohlins. It will need to be revalved straight away. Send it over to Steve Mudford. He did all the work on the Kawasaki stuff over the last few years and knows what they need in valving and set up terms. Your Adelaide suspension guy might be good, but Mudford is Great.

[Jonno]

Jonno, don't fuck around with your Ohlins. It will need to be revalved straight away. Send it over to Steve Mudford. He did all the work on the Kawasaki stuff over the last few years and knows what they need in valving and set up terms. Your Adelaide suspension guy might be good, but Mudford is Great.

Will do, should I get him to do the forks as well.













/

[MAXUMIS]

Shit Jonno just when im happy with my performance you throw it into another EXTREME now im going to have to up the anti alot to scrub those fairings in PS great pic mate!!

[Wattie]

I quite like this pic of Jonno's bike...

[Jonno]

I think you WANT that bike

And yeah you showed me how much faster I could go on it too

[tim]

I quite like this pic of Jonno's bike...

Who took that Wattie?

[born green]

Jonno, don't fuck around with your Ohlins. It will need to be revalved straight away. Send it over to Steve Mudford. He did all the work on the Kawasaki stuff over the last few years and knows what they need in valving and set up terms. Your Adelaide suspension guy might be good, but Mudford is Great.

2nd that...
His the the man... what he has just done to my 10 is amazing.. can not speak high enough of steve... and he came up to broady to dial it in... u just cant beat that service.. and he's a dam nice guy to.

And not only kawaka's either, he said he worked with yamaha as well, and i beleive he did some work with that other jap brand that starts with a S

[Wattie]

I think you WANT that bike

And yeah you showed me how much faster I could go on it too

fuck HSV!

"2011 ZX10R, I Just want one!"

[Wattie]

it will be a completely different bike, just with a rear spring Change.

I'd suggest putting the stock Ohlins in, ride it and go to someone with some feedback.
Its horses for courses.

[Wattie]

wheres that other pic Jonno?

its hows how much the geometry of the bike changes. theres one form the other side at turn 2. the belly pan is paralel with the ground as you are coasting (or little gas) then the one you put up you are rolling on the gas, it shows how bad the squat is.

[Jonno]

it will be a completely different bike, just with a rear spring Change.

I'd suggest putting the stock Ohlins in, ride it and go to someone with some feedback.
Its horses for courses.

I agree but for what its worth I wont bother with the oem unit yet, yeah that's the plan then get the bike over to Steve Mudford probably do a Winton TD while there. He is the closest of the highly recommended guys I have heard of, might as well get the best job possible.

wheres that other pic Jonno?

its hows how much the geometry of the bike changes. theres one form the other side at turn 2. the belly pan is paralel with the ground as you are coasting (or little gas) then the one you put up you are rolling on the gas, it shows how bad the squat is.

Eastern Creek T2

2 exit.jpg (106.66 KiB) Viewed 2004 times

[Phil]

Jonno, don't fuck around with your Ohlins. It will need to be revalved straight away. Send it over to Steve Mudford. He did all the work on the Kawasaki stuff over the last few years and knows what they need in valving and set up terms. Your Adelaide suspension guy might be good, but Mudford is Great.

2nd that...
His the the man... what he has just done to my 10 is amazing.. can not speak high enough of steve... and he came up to broady to dial it in... u just cant beat that service.. and he's a dam nice guy to.

And not only kawaka's either, he said he worked with yamaha as well, and i beleive he did some work with that other jap brand that starts with a S

\
Correct, Steve was Jamie Stauffer's suspension man when he won the two SBK and Supersport Totles with Yamaha. He has also looked after Brodie and Nick Waters Sunstate/Water Racing Suzukis and Tim Mcgregor who was riding a ZX-6R in Superstock but is now on a Trump 675R Daytona, so yeh, he has just about everything covered.

As has also been said before he is a top bloke as well, Technical Partners Suspension is his company . I've got all his deatils if you need em to mate

[Blurr]

I quite like this pic of Jonno's bike...

Jonno's bike is a slut

another good pic

PI 2011 3.jpg (144.51 KiB) Viewed 1992 times

[born green]

Jonno, don't fuck around with your Ohlins. It will need to be revalved straight away. Send it over to Steve Mudford. He did all the work on the Kawasaki stuff over the last few years and knows what they need in valving and set up terms. Your Adelaide suspension guy might be good, but Mudford is Great.

2nd that...
His the the man... what he has just done to my 10 is amazing.. can not speak high enough of steve... and he came up to broady to dial it in... u just cant beat that service.. and he's a dam nice guy to.

And not only kawaka's either, he said he worked with yamaha as well, and i beleive he did some work with that other jap brand that starts with a S

\
Correct, Steve was Jamie Stauffer's suspension man when he won the two SBK and Supersport Totles with Yamaha. He has also looked after Brodie and Nick Waters Sunstate/Water Racing Suzukis and Tim Mcgregor who was riding a ZX-6R in Superstock but is now on a Trump 675R Daytona, so yeh, he has just about everything covered.

As has also been said before he is a top bloke as well, Technical Partners Suspension is his company . I've got all his deatils if you need em to mate

Thort he had worked on suzuki's, wasnt a 100% on that.
He rang me a couple of days after sat track day to see how the last session went as well, he said he's just a phone call away, if im anywhere, and need some advise..... the guys a champ...