Does anyone have a good source locally (Sydney) ? Thinking about converting my '07 10 to a single zorst, by getting a mid pipe made up to suit the Akrapovic.
Thanks,
Brian
Kawasaki Sportsbike Riders Club - Australia - Online Forum
Australian Kawasaki Sportsbike Riders Discussion Forum - All Welcome, free and easy to join, just click "register" below - www.ksrc-au.com
Titanium fabrication / welding
5 posts
• Page 1 of 1
Titanium fabrication / welding
by greenman43 » Tue Jun 21, 2011 7:49 pm
07 ZX10R track 09 ZX6R road/track 93 ZXR750 race 89 GPZ900 project
Do not walk behind me, for I may not be leading
Do not walk in front of me, for I may not be following
Do not walk alongside me, for the path may be narrow
Just piss off and leave me alone
Do not walk behind me, for I may not be leading
Do not walk in front of me, for I may not be following
Do not walk alongside me, for the path may be narrow
Just piss off and leave me alone
-
greenman43 - KSRC Regular
- Posts: 675
- Joined: Fri May 06, 2005 10:01 pm
- Location: Brooklyn NSW
- Bike: ZX6R
- State: New South Wales
Re: Titanium fabrication / welding
by mike-s » Tue Jun 21, 2011 10:10 pm
Titanium is a bitch to manufacture/weld compared to other metals, custom stainless would be a shitload easier (i.e. cheaper for you).
If it hurts, you aren't doing it right.
-
mike-s - Apprentice Post Whore :-)
- Posts: 6142
- Joined: Sat Aug 07, 2004 5:43 am
- Location: Arncliffe, Sydney
- Bike: Suzuki
- State: New South Wales
Re: Titanium fabrication / welding
by greenman43 » Wed Jun 22, 2011 11:20 pm
Thanks Mike, I know it won't be cheap, but I'd prefer to keep the whole system in ti.
Cheers,
Brian
Cheers,
Brian
07 ZX10R track 09 ZX6R road/track 93 ZXR750 race 89 GPZ900 project
Do not walk behind me, for I may not be leading
Do not walk in front of me, for I may not be following
Do not walk alongside me, for the path may be narrow
Just piss off and leave me alone
Do not walk behind me, for I may not be leading
Do not walk in front of me, for I may not be following
Do not walk alongside me, for the path may be narrow
Just piss off and leave me alone
-
greenman43 - KSRC Regular
- Posts: 675
- Joined: Fri May 06, 2005 10:01 pm
- Location: Brooklyn NSW
- Bike: ZX6R
- State: New South Wales
Re: Titanium fabrication / welding
by mick41zxr » Tue Jun 28, 2011 10:42 pm
Brian,
Can be done, you can either do it in a gas bath or purge weld with a trailing cup.
Send me a message & I will email my contact details.
Regards,
Michael
Can be done, you can either do it in a gas bath or purge weld with a trailing cup.
Send me a message & I will email my contact details.
Regards,
Michael
- mick41zxr
- Newbie
- Posts: 1
- Joined: Tue Jun 28, 2011 10:39 pm
- Bike: ZXR400
- State: New South Wales
Re: Titanium fabrication / welding
by Icey_Cold » Wed Jun 29, 2011 6:23 pm
hey brian,
my mate has a 2007 zx10r with a racefit titanium exhaust (single exhaust to the side), it goes straight to the stock headers which i've been told are also titanium? is that what you were after?
my mate has a 2007 zx10r with a racefit titanium exhaust (single exhaust to the side), it goes straight to the stock headers which i've been told are also titanium? is that what you were after?
- Icey_Cold
- Newbie
- Posts: 27
- Joined: Wed Jun 15, 2011 11:36 am
- Bike: ZX10R
- State: ACT
5 posts
• Page 1 of 1
Return to General Tech & Performance Talk
Who is online
Users browsing this forum: No registered users and 11 guests